95 S-10 Truggy Build - Page 6

93 Krawler · 01-17-2019, 01:26 PM

Quote:

Originally Posted by 93 Krawler

I need to make new driveshafts, so I need yokes and tubing. What is the OD and wall thickness of what you're using? I need to know what's holding up to the abuse we put them through. The last ones I built I used the 2 1/8 DOM I had laying around. I want to use something more common this time.

I also need to know how much slip to use on a linked suspension. I know it won't move as much as it did with the leaf springs. Knowing the diameter of the spline would help too.

I guess no one has driveshafts...

Runoveru2 · 01-17-2019, 01:41 PM

I do but I have a yoda..
I run 1/4 wall Dom.
Don't remember diameter right off,
Would have to measure.
I wouldn't make anything less than 1/4 wall.
I bent or twisted anything less.

94Dodge Truggy · 01-17-2019, 02:56 PM

Quote:

Originally Posted by 93 Krawler

I need to make new driveshafts, so I need yokes and tubing. What is the OD and wall thickness of what you're using? I need to know what's holding up to the abuse we put them through. The last ones I built I used the 2 1/8 DOM I had laying around. I want to use something more common this time.

I also need to know how much slip to use on a linked suspension. I know it won't move as much as it did with the leaf springs. Knowing the diameter of the spline would help too.

I run .1875" wall tube. 14" of slip is good. Too heavy can eat up parts. Best weak link is driveshafts.

Smiddy24 · 01-17-2019, 03:21 PM

Quote:

Originally Posted by 93 Krawler

I guess no one has driveshafts...

I told you what my measurements were. Guessing you need a whole driveshaft?

beer_goggles_009 · 01-19-2019, 11:30 AM

Tom woods uses 2" .120 wall for driveshafts.

Sent from my Pixel using Tapatalk

bbtank45 · 01-19-2019, 11:40 AM

I used 2", 1/4 wall DOM. Ordered my yolks from Northern Drivetrain and Carolina Driveline machined to fit. Made them in the buggy.

Sent from my SM-G950U using Tapatalk

93 Krawler · 01-23-2019, 05:41 PM

I ended up buying parts for 2 in quarter wall tubing. Has about seven and a half inches of total slip. This should be plenty strong.

Sent from my S7 using Tapatalk

93 Krawler · 01-31-2019, 07:27 PM

Been working on getting the tcase tucked in and making a sturdy crossmember. My last one was bent up, so I beefed this up. Had to cut a big hole in the floor to get the tcase up where i wanted it. Still sticks out the bottom an inch. So much for a flat belly pan. Oh well, it will be mostly flat...

Click image for larger version

Name: 20190131_190909.jpeg
Views: 26
Size: 80.7 KB
ID: 10287

Click image for larger version

Name: 20190131_190927.jpeg
Views: 27
Size: 90.4 KB
ID: 10288

Click image for larger version

Name: 20190131_191134.jpeg
Views: 26
Size: 101.2 KB
ID: 10289

Click image for larger version

Name: 20190131_191532.jpeg
Views: 26
Size: 95.2 KB
ID: 10290

Click image for larger version

Name: 20190131_191542.jpeg
Views: 25
Size: 93.2 KB
ID: 10291

Sent from my S7 using Tapatalk

93 Krawler · 02-05-2019, 09:17 PM

Got my t case shifters mounted in my console. Worked out perfectly by cutting out the square junk tray.

Click image for larger version

Name: 20190205_194944.jpeg
Views: 16
Size: 54.8 KB
ID: 10292

Click image for larger version

Name: 20190205_194934.jpeg
Views: 16
Size: 80.9 KB
ID: 10293

Sent from my S7 using Tapatalk

jeepmanjeff · 02-06-2019, 06:26 PM

Man that turned out great!

Sent from my iPhone using Tapatalk

93 Krawler · 02-18-2019, 08:25 PM

Since I run an electronic trans I needed to add a vss to the system. Luckily the ford np205 has the same 32 spline output as my np241 had. Drilled and tapped the case for the stock vss, and also had to remove about 1/4" off the reluctor ring width. So for a few hrs work and zero cost I have my oem vss setup.

Click image for larger version

Name: 20190215_192949.jpeg
Views: 21
Size: 95.5 KB
ID: 10307

Sent from my S7 using Tapatalk

93 Krawler · 02-21-2019, 08:46 AM

Got the front end back on. Now i can build the frame from the firewall to the core support.

Click image for larger version

Name: 20190220_193024.jpeg
Views: 22
Size: 100.2 KB
ID: 10309

Click image for larger version

Name: 20190220_193000.jpeg
Views: 22
Size: 91.2 KB
ID: 10308

Sent from my S7 using Tapatalk

Smiddy24 · 02-21-2019, 11:21 AM

Lookin good, almost there man!

Ky Mudhunter · 02-21-2019, 12:12 PM

I did the same thing on my Ford 205 for the speed sensor. I couldn't believe how easy it was to add.

Runoveru2 · 02-21-2019, 02:17 PM

Looking good, when are the axles going under it ?

Smiddy24 · 02-21-2019, 02:18 PM

Quote:

Originally Posted by Runoveru2

Looking good, when are the axles going under it ?

^^^^^^

93 Krawler · 02-21-2019, 08:06 PM

Quote:

Originally Posted by Runoveru2

Looking good, when are the axles going under it ?

Not soon enough. I'll most likely get the engine wired up before the axles go in.

Sent from my S7 using Tapatalk

Smiddy24 · 03-11-2019, 12:08 PM

Any update?

93 Krawler · 03-12-2019, 08:44 PM

I missed a week working on it cuz i was sick.
I got the pcm and fuse block mounted, frame and motor mounts done. Winch is ready to mount, and core support cut down to mount on frame.

Click image for larger version

Name: 20190312_183113.jpeg
Views: 23
Size: 91.5 KB
ID: 10314

Click image for larger version

Name: 20190312_192250.jpeg
Views: 27
Size: 123.8 KB
ID: 10315

Click image for larger version

Name: 20190312_192303.jpeg
Views: 26
Size: 109.8 KB
ID: 10316

Click image for larger version

Name: 20190312_195847.jpeg
Views: 28
Size: 128.3 KB
ID: 10317

Sent from my S7 using Tapatalk

jeepmanjeff · 03-24-2019, 07:56 PM

Welded up the trusses, link brackets and set them in place today with Kevin. Gonna be really sweet when done.

Click image for larger version

Name: IMG_1227.jpg
Views: 23
Size: 54.5 KB
ID: 10331

Click image for larger version

Name: IMG_1226.jpg
Views: 24
Size: 71.6 KB
ID: 10332

Click image for larger version

Name: IMG_1229.jpg
Views: 25
Size: 92.7 KB
ID: 10333

Click image for larger version

Name: IMG_1230.jpg
Views: 23
Size: 81.8 KB
ID: 10334

Sent from my iPhone using Tapatalk

93 Krawler · 03-26-2019, 10:58 PM

That was a big help, thanks. Like 4 hrs of welding. Finally got the axles under the rig. Got the front and rear truss installed. The front and rear 4 links are almost done.

My last trip to Harlan i lost my pinion bearing. I was sure the gears were destroyed, but luckily there wasn't much damage to the teeth.

Click image for larger version

Name: 20190317_180441.jpeg
Views: 26
Size: 109.3 KB
ID: 10335

Click image for larger version

Name: 20190324_160021.jpeg
Views: 28
Size: 105.5 KB
ID: 10337

Click image for larger version

Name: 20190324_160013.jpeg
Views: 27
Size: 89.5 KB
ID: 10338

Click image for larger version

Name: 20190317_201301.jpeg
Views: 24
Size: 109.8 KB
ID: 10339

Sent from my S7 using Tapatalk

93 Krawler · 04-03-2019, 12:41 PM

Working on the shocks now.

Click image for larger version

Name: 20190330_155358.jpg
Views: 21
Size: 118.5 KB
ID: 10344

Click image for larger version

Name: 20190331_180321.jpg
Views: 21
Size: 101.6 KB
ID: 10345

Click image for larger version

Name: 20190328_194709.jpg
Views: 21
Size: 108.6 KB
ID: 10346

Click image for larger version

Name: 20190328_194728.jpg
Views: 21
Size: 134.4 KB
ID: 10347

Click image for larger version

Name: 20190330_151855.jpg
Views: 22
Size: 137.3 KB
ID: 10348

Click image for larger version

Name: 20190330_151909.jpg
Views: 21
Size: 102.9 KB
ID: 10349

Click image for larger version

Name: 20190331_200734.jpg
Views: 25
Size: 105.2 KB
ID: 10350

Click image for larger version

Name: 20190331_200739.jpg
Views: 23
Size: 124.9 KB
ID: 10351

Click image for larger version

Name: 20190331_180334.jpg
Views: 26
Size: 114.1 KB
ID: 10352

93 Krawler · 05-09-2019, 04:22 PM

Back is done except the aluminum panel for my turn signals and reverse lights.

Click image for larger version

Name: 20190508_210856.jpg
Views: 24
Size: 97.3 KB
ID: 10377

Click image for larger version

Name: 20190508_210846.jpg
Views: 25
Size: 88.7 KB
ID: 10378

Sent from my S7 using Tapatalk

jeepmanjeff · 05-10-2019, 09:39 AM

Looking awesome! Let me know when you want that aluminum

Sent from my iPhone using Tapatalk

93 Krawler · 05-14-2019, 11:46 AM

Quote:

Originally Posted by jeepmanjeff

Looking awesome! Let me know when you want that aluminum

Sent from my iPhone using Tapatalk

Thanks, will do. Tim has a piece of stainless I might use instead. Depends on how it looks.

01-17-2019, 01:41 PM	#127
Runoveru2 Adrenaline Junkie - CORE Member - - Moderator - Join Date: Jun 2011 Location: Hamilton, Ohio Posts: 702 Images: 168	I do but I have a yoda.. I run 1/4 wall Dom. Don't remember diameter right off, Would have to measure. I wouldn't make anything less than 1/4 wall. I bent or twisted anything less. __________________ No need for a Winch...You just have to make it !!

01-19-2019, 11:40 AM	#131
bbtank45 Join Date: Sep 2011 Location: Ross, OH Posts: 200	I used 2", 1/4 wall DOM. Ordered my yolks from Northern Drivetrain and Carolina Driveline machined to fit. Made them in the buggy. Sent from my SM-G950U using Tapatalk __________________ 1985 4runner "Redneck Gigalo"

01-31-2019, 07:27 PM	#133
93 Krawler >>>PMC<<< - CORE Member - - Administrator - Join Date: Sep 2010 Location: Ross, OH Posts: 2,069 Images: 1268	Been working on getting the tcase tucked in and making a sturdy crossmember. My last one was bent up, so I beefed this up. Had to cut a big hole in the floor to get the tcase up where i wanted it. Still sticks out the bottom an inch. So much for a flat belly pan. Oh well, it will be mostly flat... Sent from my S7 using Tapatalk Last edited by 93 Krawler; 03-11-2019 at 04:33 PM.

02-05-2019, 09:17 PM	#134
93 Krawler >>>PMC<<< - CORE Member - - Administrator - Join Date: Sep 2010 Location: Ross, OH Posts: 2,069 Images: 1268	Got my t case shifters mounted in my console. Worked out perfectly by cutting out the square junk tray. Sent from my S7 using Tapatalk

02-06-2019, 06:26 PM	#135
jeepmanjeff Ah Unz ze President! - CORE Member - - Moderator - Join Date: Jan 2007 Location: Fairfield Ohio Posts: 588 Images: 343	Man that turned out great! Sent from my iPhone using Tapatalk __________________ Keep them on all 4's

01-19-2019, 11:30 AM	#130
beer_goggles_009 - CORE Member - Join Date: Apr 2011 Location: Mt Washington Posts: 188	Tom woods uses 2" .120 wall for driveshafts. Sent from my Pixel using Tapatalk

01-23-2019, 05:41 PM	#132
93 Krawler >>>PMC<<< - CORE Member - - Administrator - Join Date: Sep 2010 Location: Ross, OH Posts: 2,069 Images: 1268	I ended up buying parts for 2 in quarter wall tubing. Has about seven and a half inches of total slip. This should be plenty strong. Sent from my S7 using Tapatalk

02-18-2019, 08:25 PM	#136
93 Krawler >>>PMC<<< - CORE Member - - Administrator - Join Date: Sep 2010 Location: Ross, OH Posts: 2,069 Images: 1268	Since I run an electronic trans I needed to add a vss to the system. Luckily the ford np205 has the same 32 spline output as my np241 had. Drilled and tapped the case for the stock vss, and also had to remove about 1/4" off the reluctor ring width. So for a few hrs work and zero cost I have my oem vss setup. Sent from my S7 using Tapatalk

02-21-2019, 08:46 AM	#137
93 Krawler >>>PMC<<< - CORE Member - - Administrator - Join Date: Sep 2010 Location: Ross, OH Posts: 2,069 Images: 1268	Got the front end back on. Now i can build the frame from the firewall to the core support. Sent from my S7 using Tapatalk

02-21-2019, 11:21 AM	#138
Smiddy24 2019 Custom CJ7 Buggy - CORE Member - Join Date: Dec 2015 Location: Fairfield, Ohio Posts: 448 Images: 72	Lookin good, almost there man! __________________ You got it"

02-21-2019, 12:12 PM	#139
Ky Mudhunter Join Date: May 2013 Posts: 75	I did the same thing on my Ford 205 for the speed sensor. I couldn't believe how easy it was to add.

02-21-2019, 02:17 PM	#140
Runoveru2 Adrenaline Junkie - CORE Member - - Moderator - Join Date: Jun 2011 Location: Hamilton, Ohio Posts: 702 Images: 168	Looking good, when are the axles going under it ? __________________ No need for a Winch...You just have to make it !!

03-11-2019, 12:08 PM	#143
Smiddy24 2019 Custom CJ7 Buggy - CORE Member - Join Date: Dec 2015 Location: Fairfield, Ohio Posts: 448 Images: 72	Any update? __________________ You got it"

03-12-2019, 08:44 PM	#144
93 Krawler >>>PMC<<< - CORE Member - - Administrator - Join Date: Sep 2010 Location: Ross, OH Posts: 2,069 Images: 1268	I missed a week working on it cuz i was sick. I got the pcm and fuse block mounted, frame and motor mounts done. Winch is ready to mount, and core support cut down to mount on frame. Sent from my S7 using Tapatalk

03-24-2019, 07:56 PM	#145
jeepmanjeff Ah Unz ze President! - CORE Member - - Moderator - Join Date: Jan 2007 Location: Fairfield Ohio Posts: 588 Images: 343	Welded up the trusses, link brackets and set them in place today with Kevin. Gonna be really sweet when done. Sent from my iPhone using Tapatalk __________________ Keep them on all 4's

03-26-2019, 10:58 PM	#146
93 Krawler >>>PMC<<< - CORE Member - - Administrator - Join Date: Sep 2010 Location: Ross, OH Posts: 2,069 Images: 1268	That was a big help, thanks. Like 4 hrs of welding. Finally got the axles under the rig. Got the front and rear truss installed. The front and rear 4 links are almost done. My last trip to Harlan i lost my pinion bearing. I was sure the gears were destroyed, but luckily there wasn't much damage to the teeth. Sent from my S7 using Tapatalk

04-03-2019, 12:41 PM	#147
93 Krawler >>>PMC<<< - CORE Member - - Administrator - Join Date: Sep 2010 Location: Ross, OH Posts: 2,069 Images: 1268	Working on the shocks now.

05-09-2019, 04:22 PM	#148
93 Krawler >>>PMC<<< - CORE Member - - Administrator - Join Date: Sep 2010 Location: Ross, OH Posts: 2,069 Images: 1268	Back is done except the aluminum panel for my turn signals and reverse lights. Sent from my S7 using Tapatalk

05-10-2019, 09:39 AM	#149
jeepmanjeff Ah Unz ze President! - CORE Member - - Moderator - Join Date: Jan 2007 Location: Fairfield Ohio Posts: 588 Images: 343	Looking awesome! Let me know when you want that aluminum Sent from my iPhone using Tapatalk __________________ Keep them on all 4's